guzziriders.org - moto guzzi forum Homepage
Forum Home Forum Home > Introduction > Introduce yourself
  New Posts New Posts RSS Feed - V11 sport front spindle /axle.
  FAQ FAQ  Forum Search   Events   Register Register  Login Login

V11 sport front spindle /axle.

 Post Reply Post Reply Page  <12
Author
Message
Brian UK View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 13 May 2014
Location: Surrey
Status: Offline
Points: 17641
Post Options Post Options   Thanks (0) Thanks(0)   Quote Brian UK Quote  Post ReplyReply Direct Link To This Post Posted: 20 Jun 2020 at 21:32
OK, I admit I'm confused.
The wheel spindle is threaded at one end, but surely there is a nut which goes on there? It doesn't thread into the fork bottom direct does it?
I'm just going from the parts list here.
Brian.

Better 5 minutes late in this world than years early in the next.
Back to Top
Ken-Guzzibear View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 13 May 2014
Location: Sileby Leics
Status: Offline
Points: 9454
Post Options Post Options   Thanks (0) Thanks(0)   Quote Ken-Guzzibear Quote  Post ReplyReply Direct Link To This Post Posted: 20 Jun 2020 at 22:08
Tony if you measure the pitch ....gaps in the thread on the spindle and the diameter of the spindle at the thread that gives the same numbers. Brian the EV has threads inside bottom left fork leg with spacer wound in by 14 mm hex socket the pinch  bolts are on the right fork leg, I think Tony is getting mixed up hence the above ...On older bikes like my 76 V1000 the front spindle goes in on the left that has the spacer the right side then has a bloomin' big nut on it .... 
The Older i Get, The Better I Was
Back to Top
Tony. W-H View Drop Down
Falcone
Falcone
Avatar

Joined: 19 Jun 2020
Location: Cornwall
Status: Offline
Points: 18
Post Options Post Options   Thanks (0) Thanks(0)   Quote Tony. W-H Quote  Post ReplyReply Direct Link To This Post Posted: 22 Jun 2020 at 14:00
Well ive managed to find the thread size for my v11 sport front wheel fork spindle. Some very helpful chaps I Hayle Cornwall measured the spindle thread for me. It is 18mm x 1.5 pitch

Back to Top
Brian UK View Drop Down
Moderator Group
Moderator Group
Avatar

Joined: 13 May 2014
Location: Surrey
Status: Offline
Points: 17641
Post Options Post Options   Thanks (0) Thanks(0)   Quote Brian UK Quote  Post ReplyReply Direct Link To This Post Posted: 22 Jun 2020 at 17:48
How are you going to get the helicoil fitted?
Brian.

Better 5 minutes late in this world than years early in the next.
Back to Top
Dave P. View Drop Down
Senior Member
Senior Member
Avatar

Joined: 12 Jan 2015
Location: Northants
Status: Offline
Points: 5573
Post Options Post Options   Thanks (0) Thanks(0)   Quote Dave P. Quote  Post ReplyReply Direct Link To This Post Posted: 22 Jun 2020 at 19:44
Good question. Don't try to do it in situ'.
TO LIVE OUTSIDE THE LAW YOU MUST BE HONEST.

1971 V7 Special. 1972 850GT.
1970 T120 Bonnie. 2009 500 Bullet.
Back to Top
 Post Reply Post Reply Page  <12
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 12.03
Copyright ©2001-2019 Web Wiz Ltd.

This page was generated in 0.063 seconds.